суббота, 2 декабря 2017 г.

Rustic X DIY Changing Table

Rustic X Changing Table - Feature
.*
TedsWoodworking Plans and Projects
Rustic X Changing Table - Front, Unfinished
Unfinished, front view
Rustic X Changing Table - Front, Unfinished
Unfinished, side view
Rustic X Changing Table - Double as bunk beds
It doubles as bunk beds

With a new baby on the way the list of projects can seem to be endless. One that was at the top of the list was a DIY changing table. My inspiration for this DIY changing table came from the Pottery Barn Belmont buffet and if you want to build that take a look at Ana White’s plans for it. Below I have provided detailed baby changing table woodworking plans for you to enjoy. Please post your results in the comments.

  • 1x 1 x 4 x 8′
  • 1x 1 x 4 x 6′
  • 4x 2 x 2 x 8′
  • 3x 2 x 3 x 8′
  • 5x 2 x 6 x 8′
  • 1x 1/4 x 24 x 48″ plywood (I went with sandply)

Recommended Changing Pad: Summer Infant 4-Sided Changing Pad

When I started building furniture in my free time I always wanted to see it come together as fast as possible. Even though maybe the frame came together quickly the rest took some time. Thats why I now cut most/all my wood at once and I recommend you do the same. Hopping between the saw and the pocket hole jig waste a lot of time, and if your free time is limited like mine you’ll agree in the end that this is the only way to go.

Cut List: Rustic X DIY Changing Table
Cut List: Print this out
Angled Cuts: Rustic X DIY Changing Table
Angled Cuts: Print this out

Before you get started… sand, sand, SAND!

It is best to sand all the cut wood before you start assembling. It’s so much easier to do now then once its assembled especially with all the tight corners. Please know that this kills me too, but I promise its worth it and you’ll be thanking me in the end. For a more in depth instructions take a look at our how to sand whitewood post.

As always if you have any questions don’t hesitate to comment below and especially don’t forget to post pictures of your finished products in the comments! ENJOY!

Step 1: Rustic X DIY Changing Table
Step 1: Assemble sides together (Make two of these!)

Step 1: Assembling sides

Drill pocket holes in each end of the 15in 2×2’s. Next, screw and glue them to the 31.5in 2×3’s as shown in the picture. Remember, we need two of these.

Note: Know that the pocket holes will be on the inside of the changing table, therefore, you should choose the uglier sides of your wood to be on this side.

Step 2: Rustic X DIY Changing Table
Step 2: Screw in longer diagonal slat.

Step 2: Assembling sides

Attach the longer angled 2×2 with 2″ wood screws from the top and the bottom as shown. Make sure to glue these joints as well.

Step 3: Rustic X DIY Changing Table
Step 3: Screw in upper slat.

Step 3: Assembling sides

Screw and glue the smaller angled 2×2 in the upper right position with 2″ wood screws. As shown, place the lower screw slightly off from center and at an angle of the 2×2. (As you can see in the next step we will be coming right behind it with a pocket hole screw.)

Step 4: Rustic X DIY Changing Table
Step 4: Screw in lower slat.

Step 4: Assembling sides

Using the Kreg jig, drill a pocket hole in the remaining smaller angled 2×2’s as shown in the picture. (Make sure you pocket hole is in the correct side)

Screw and glue the lower slat of the X in with one 2″ wood screw and one 2-1/2″ pocket hole screw, as shown.

Step 5: Rustic X Changing Table
Step 5: Assembling the top

Step 5: Assembling Top

Drill four pocket holes, evenly spaced, in three of the 49 inch 2×6’s. You should choose the uglier sides of your wood to be on this side.

Clamp to maintain a flat surface and screw and glue together, as shown, with 2-1/2″ pocket hole screws.

I suggest giving this another sanding to smooth the top once assembled.

Step 6: Rustic X DIY Changing Table
Step 6: Assemble middle shelf

Step 6: Assembling Middle Shelf

Drill pocket holes, evenly spaced, in the three 44 inch 2×6’s as shown in the picture. You should choose the uglier sides of your wood to be on this side.

Clamp to maintain a flat surface and screw and glue the three 2×6’s and two 2×2’s together, as shown, with 2-1/2″ pocket hole screws.

I suggest giving this another sanding to smooth the top once assembled.

Step 7 - Bottom Shelf, Rustic X DIY Changing Table
Step 7: Assemble bottom shelf

Step 7: Assembling Bottom Shelf

Drill pocket holes, evenly spaced, in the three 44 inch 2×6’s as shown in the picture. You should choose the uglier sides of your wood to be on this side.

Clamp to maintain a flat surface and screw and glue the three 2×6’s, sandwiched between the 2×2 and the 2×3, as shown, with 2-1/2″ pocket hole screws.

I suggest giving this another sanding to smooth the top once assembled.

Step 8 - Table Assembly (Part A), Rustic X DIY Changing Table
Step 8: Attach the shelves and top rails to one side

Step 8: Assembling Table

Drill the pocket holes, as shown in the shelves and upper rails. Make sure to notice that the middle shelf has three pocket holes, one at each end and one at the middle of the X (this is not the center). Make sure the back of the shelves are flush with the back of the side first and mark where your pocket holes should go.

With the top rails flush with the outside top corners of the side panels, attach with 2″ pocket hole screws as shown. Assure that your shelves are square and attach with 2″ pocket hole screws as shown.

Step 9 - Table Assembly, Rustic X DIY Changing Table
Step 9: Attach the opposite side

Step 9: Assembling Table

With the top rails flush with the outside top corners of the side panels, attach with 2″ pocket hole screws as shown. Assure that your shelves are square and attach with 2″ pocket hole screws as shown.

Step 10 - Table Assembly, Rustic X DIY Changing Table
Step 10: Screw on the top

Step 10: Assembling Table

Finish off your table by adding the top. To do so you should drill four pocket holes in the back rail (2×3), as shown.

Attach the top with four 2″ pocket hole screws in the back rail and 2″ wood screws through the 2×2’s as designated by the arrows in the picture.

Step 11 - Back Panel, Rustic X DIY Changing Table
Step 11: Adding the back panel

Step 11: Adding Back Panel

Cut your 1/4″ plywood to 24×45.5″ and nail or screw it to the back as shown in the photo. It is wise to draw a line across the back to show you where to nail.

Note: I used a finishing nailer for this with 1-1/4″ brads but if you don’t have a nailer you can just as well use screws.

Step 12 - Topper, Rustic X DIY Changing Table
Step 12: Assembling the Topper

Step 12: Assembling Topper

Drill your pocket holes at each end of the 1x4x17″ boards. (Make sure to adjust your jig for 1″ material).

Make sure to place your pocket holes where they will be the best concealed. The two boards on the right in the picture should actually have the holes on the opposite side (But I can’t show that now can I?). Assemble your topper as shown with 1-1/4″ pocket hole screws, making sure to glue the joints.

Important Note:

If your going to stain the top like we did then now is a good time to do so. Make sure to stain both the top and the topper prior to installing the topper.

Step 13 - Final Assembly, Rustic X Changing Table
Step 13: Installing the Topper

Step 13: Installing Topper

Drill the pocket holes as shown, except for the right hand board, those should be on the opposite side to best conceal them.

Attach the topper with with 1-1/4″ pocket hole screws.

Complete - Rustic X DIY Changing Table
Complete – Rustic X DIY Changing Table

By: Jamie Rantz (aka Rogue Engineer’s wife)

To be completely honest with you, I had no clue where this project was headed when I started it. I just knew that I wanted the finished piece to be something I could use anywhere in my house and not just as a changing table. When I woke up that morning and actually had energy, which doesn’t happen often being 8 months pregnant, I went out to the garage and started throwing things together.

I wasn’t sure if I wanted a distressed look, but I wanted the option to do so just in case! With that in mind here is the combination of finishes I chose to go with.

As always if you have any questions don’t hesitate to comment below and especially don’t forget to post pictures of your finished products in the comments! ENJOY!

Original article and pictures take http://rogueengineer.com/rustic-x-diy-changing-table-plans/ site

Комментариев нет:

Отправить комментарий